Home  »  Tech Support

ACDC CODING INSTRUCTIONS

ROLLER-GLIDE

 CODING REMOTES

 Remove the white plastic light diffuser - Beware of connected Push buttonattached.

Pressthe button on the remote you wish to operate this door for 2 seconds
Pause for 2 seconds
Press the same button again for 2 seconds

Up to 25 remote controls may be used

 
DELETING REMOTES

Toerase existing remote controls press and hold the LEARN button for 15 seconds

 POWER-GLIDE& EURO-GLIDE

CODING REMOTES

Pressand release LEARN button - A dot will be indicated in the corner of the LEDdisplay.

Pressthe button on the remote you wish to operate this door for 2 seconds
Pause for 2 seconds
Press the same button again for 2 seconds.

The dotin the corner of the display will flash to confirm the code and then turn off.

 Repeatthis process for additional Remotes that need to be stored.

 Note: The POWER-GLIDE &EURO-GLIDE operators are fitted with Last Code Deleted which 
means that only one button per remote can be stored to operate the unit. Thisfunction prevents 
over coding stored Remotes when there are multiple users accessing the samegarage door.  
The other three buttons on the Remote can be programmed to access automaticgates, security 
or courtesy lights, etc.


SLIM-GLIDE

Removethe light diffuser cover. 
Press K1 button on the control board, the coding light will come on. 

Press the button on the remote you wish to operate this door for 2 seconds thecoding light will turn off, 
pause for 2 seconds,
Press the same button again for 2 seconds

The coding light will flash 8 times then turn off indicating the transmitterhas been coded successfully

Repeat the procedure for additional remote control transmitters

The Slim-Glide operator can store up to 20 remotes


DELETING REMOTES

To delete all codes press and hold button K1 down for approximately 8-10seconds (code light will come
on and then go off indicating a successful delete).


ACDC GL24

Press and hold down button "P2" MEMO: The LED "L4" willflash slowly.
At the same time activate the remote button which is to be coded
Hold down button "P2" MEMO until LED "L4" starts to flashgain.
Release the button "P2" MEMO: The LED will continue to flash.
Within 15 seconds activate the remote button again 

Note: same transmitter, same button; if the button is different or it is adifferent remote the coding attempt will abort without success

End ofcoding: the LED "L4" will remain lit for 2 seconds, indicating thatthe remote button has been 
correctly coded

Note: It is not possible to code a button which is already in memory: f youattempt this, the LED will 
switch off when you activate the button

Only after releasing the button "P2"MEMO will you be able to continuehe coding procedure.

DELETING A REMOTE

Press and hold down the button "P3" DEL: the LED "L4" willflash quickly
Activate the transmitter channel which is to be cancelled
The LED will remain lit for 2 seconds indicating that the transmitter
has been deleted

Note: If the user that you wish to cancel is not in memory, the LED will stopflashing; only after 
releasing the button "P3" will you be able to continue the deleteprocedure
.
For both the coding and cancellation procedures, if the button is releasedbefore activating the remote 
the procedure will abort.

DELETING ALL REMOTES

Keep both buttons pressed down ("P2+P3") for more than four seconds.
LED "L4" will remain lit during the entire delete time (about 8seconds).
LED "L4" switches off when the cancellation procedure has terminated

 Note:When the memory is almost full the time required to search for a user codecould take up 
to 1 second from when the command was received. If led "L4" remainslit memory is completely full. 
To code a new remote you will first have to cancel a code from memory